BEMATECH MP 4000 TH DRIVER

The communication cable may Verify the cable in all its length to be sure that it be damaged or not properly has no indication of physical damage. MP TH printer test phases. Tab ‘additional Commands Tab ‘Additional Commands’ 1. Page 47 There is a sensor on the right side of the printer picture above that notifies it when the cover is closed. Page 31 The next steps are required in order to remove the thermal print head. To separate the connection board from the cutter mechanism, start by loosening the screw that holds the grounding cable located on the side of the equipment, then move away the connection board and disconnect the cables. Replace the control board to address the issue.

Uploader: Vudojinn
Date Added: 8 April 2011
File Size: 67.88 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 96973
Price: Free* [*Free Regsitration Required]

The correct position to connect this cable is on the CN4 connector as shown on the image on the side. Chapter 4 – less time to replace the paper roll and, therefore, more time available for processing transactions at the retail outlet.

The product firmware update can be performed by using the ‘User’s Software’ or the ‘Technical Support Software’. To print the manual completely, please, download it.

Introduction This manual provides information on the identification and troubleshooting, test procedures and a list of replacement parts for the MP TH printer. To remove the opening Lever Set, just press it from top to bottom on the points indicated on the picture.

To remove the paper feed motor remove the elastic ring that secures the gears, then pull the gears out. Who should read this manual? Preventive Maintenance Procedures Clean the area near the cutter periodically.

Last Drivers  SHREW SOFT VIRTUAL ADAPTER DRIVER DOWNLOAD

Notice the correct way to insert the sensor on the Clean the area near the cutter periodically. Yellow LED blinking 3 times – Yh Error Verify if there is paper between the cutter and the mechanism plastic chassis. With the printer open, paper roll and spacer removed, loosen the two screws on the inside of the Printer, as shown on the right.

To remove the paper guide, just press it by its base, disconnecting it from the metal chassis as shown on the picture on the right. Removing the Cutter Mechanism, Print Head and Connection Board To access the printer interior, the cutter mechanism, thermal print head connection board, follow the steps below: By pressing ‘print’ button you will print only current page.

Tab ‘macro Tab ‘Macro’ The tab ‘Macro’ allows tests to be processed in tth mode. Bematech MP TH the ideal printing solution for your retail outlet, operating with high quality, high speed and reliability with reduced operation cost. For further information, refer to the Support section of our website www. Introduction Introduction This manual provides information on the identification and troubleshooting, test procedures and a list of replacement parts for the MP TH printer.

Verify if the connection board sensor is properly placed and if there is any dirt obstructing it. Click on the button ‘Activate’ to see the printer status. On the back side of the mechanism, there is a tab that keeps it attached to the base, as Accessories 1 Please contact Bematech to consult the availability of the interfaces and accessories.

Inner Case Make sure the printer is 44000, open the cover and remove the paper roll. On this field it is possible to make some changes in the bar code that will be printed.

Last Drivers  SAHARA LAPTOP F12DT TREIBER

If the error message persists, even if the cover is closed, you can verify the bemaatech items: There is a sensor on the right side of the printer picture above that notifies it when the cover is closed. Click on the button ‘Start’ to make a complete test of the printer.

Bematech Printer MP4000 TH User software

If there is and it’s not possible to remove it with available tools, cutter disassembly will be necessary. Below you can see the cutter mechanism, the print head and the connection board with the thermal print head connection cable. To separate the connection board from the cutter mechanism, start by loosening the screw that holds the grounding cable located on the side of the equipment, then move away the connection board and disconnect the cables.

Try to avoid disassembly, assembly and unnecessary adjustments on the MP TH parts that are working properly; 2. Bematech MP User Manual 36 pages.

Bematech MP TH Free Driver Download (Official) () – BemaSetup_MP4K_vzip

To remove the control board set, simply pull the cartridge back and then out. Configure the tests to be performed. Page 33 After disconnecting the plastic chassis, just pull up the back side to loosen the frontal part.